Introduction of led lights

White LED luminous efficiency has been a breakthrough 120LM / W, 15LM / W 8 times of incandescent, fluorescent 50LM / W 2 times. Led pool light spectrum ultraviolet and infrared components, so no heat, no harmful radiation. LED's luminous flux half-life greater than 50,000 hours, and can be used normally for 20 years, the life of the device are generally in more than 100,000 hours, which is 10 times the life of the fluorescent lamp, which is 100 times that of incandescent lamps, so basically not damaged, this lamp has a very good energy-saving long-life characteristics, continue to decrease as the price of white LED, the LED lights not only widely used in the holiday lights decoration, and gradually extended to the field of pavement lighting, commercial lighting, illumination requirements, full access to the practical and the environmental aspects of waste can be recycled, no the fluorescent mercury pollution problem, the national focus on the development of industrial projects.

 LED technology has been genuineness came to our front remarkable Olympics, both the opening ceremony on the magical picture and canvas, or the Water Cube exterior transform unpredictable colorful magic light, or a large number of actors who quintana a magical light, or even just as Galaxy and slowly rising Olympic rings, all are comprehensive application of LED technology.
 Advantage of environmental protection and energy saving led flood lighting: ◇ energy efficient: in the case of the same brightness, the one thousand hours of LED energy-saving lamps consume only 1 kWh of electricity consumption, ordinary incandescent 17 hours, one hundred hours of ordinary energy-saving lamps consume 1 degree electricity; ◇ Long life service life of up to eighty thousand hours, ten thousand hours in the life of the ordinary energy-saving lamps, ordinary incandescent lamp life of 1,000 hours. ◇ Healthy light does not contain ultraviolet and infrared energy-saving starting with me, no radiation, ordinary energy-saving lamps and incandescent light contains ultraviolet and infrared; ◇ green mercury and lead harmful elements, was conducive to the recovery and utilization , electromagnetic interference and does not produce harmful elements of ordinary lamp contains mercury and lead, and energy-saving lamps, electronic ballasts will produce electromagnetic interference; ◇ protect eyesight strobe; ◇ light efficiency high fever, 90% of the energy into visible light, ordinary incandescent DC drive, no flicker, normal lights are AC drive, it will inevitably produce 0% of the electrical energy is converted into heat, and only 20% of the electrical energy into visible light; ◇ safety factor required voltage current is small, less heat, no security risks, can be used in mines and other dangerous places; directly with 220V AC, challenges energy limit, the use of 220-volt power supply, built several pieces of miniature high-performance light-emitting beads, constant current The Manifold, design power for a small daily lighting of a lamp may meet an ordinary room, writing, reading and studying. Use ordinary meter, digital meter testing, meter basic fixed with 2 to 3 meters basically do not turn, and replacing ordinary incandescent lamp, the meter is fast rotation, the energy saving effect of immediate results, at a glance. Allow people to science, advanced, reasonable, legitimate and free electricity.

Its energy consumption as incandescent fortieth, one-third of the energy-saving lamps, intuitive and magical energy-saving effect, to attract the attention of consumers, the end of the "energy" energy-saving lamps misunderstanding is lighting lighting energy saving in the history of a major breakthrough with the epoch-making significance of innovation. 2, the health of photoinduced luminescence Manifold is the world's most state-of-the-art environmental green light, energy-saving super bright mini light beads from my start with a large angle, after layer delivery transformer, 6 to 24 volts of pure low DC drive real zero strobe, prolonged use will not make eye fatigue, with a high color rendering and high through sexual soft light approximate daylight, and does not produce color difference, can provide appropriate illumination. Work its own power consumption is minimal, so very small, fever, hand touch is an excellent and safe green cold light. Once the designer of the lights in the research and development of products based on the goal of illumination and diamond crystal point the refractive astigmatism design, light pro-and high light, through the nature of the request, the lampshade in the lamp beads Pai subcolumn point, linear, ring banded to form a more stable light source system, to achieve visual lighting with the best results. 3, LED life of up to 8-10 million hours, color stability, not of years affect the color difference.
The Source: http://www.solledlights.com http://www.led999.net/, http://www.m-queenled.com/, reproduced please specify the source, thank you!

Characteristics in the LED lighting

Led lighting led lamps collectively, using the additional maturity in the LED technology, LED will acquire additional as well as a great offer better progress through the residing space lighting the area of design and design and development. Bedroom lighting design and design through the 21st century could possibly be centered on led rigid strip lights design and design for the mainstream, completely embodies the energy, health, technique and user-friendly lighting and progress trends, the social dominant in the space lighting. through the brand new century, LED lighting lamps will certainly will brighten everyone's space to alter everyone's life, lighting progress and design and design of the awesome change.

Feature
Energy conservation review data exhibits that, in comparison with incandescent, fluorescent, ceiling led light source, semiconductor lighting for the atmosphere with out any pollution, energy-saving overall performance can attain additional than 90%. in the identical brightness, energy usage is only 1/10 of an common incandescent lamp, fluorescent tube 1/2. If 50% to replace the conventional lighting with LED, every twelve weeks of electrical power cost savings is equivalent for the sum of amid the three Gorges energy plant producing capacity, its energy overall performance is very impressive.
The well being in the LED could possibly be considered a eco-friendly light. DC LED light driver, no strobe; infrared and ultraviolet components, there is no radioactive contamination, the coloring is higher and consists of a luminous directional; common performance dimming, coloring temperatures alter does not create visual errors; chilly mild supply reduced in high fat calories and is also safe and seem to touch; they are incandescent and fluorescent reach. it could not merely provide at ease lighting space, but at the same time good to satisfy people's actual well being needs, shield their eyesight healthful and environmentally friendly mild source.
Due to scaled-down solitary LED power, reduced brightness, and should unquestionably not be utilized alone, while additional than one LED assembly produced getting sensible LED lighting consists of a broad app prospects. Lighting designers can ascertain the type in the light optical system, LED amount and sizing in the energy demands of lighting objects and luminous flux; may be also several LED LED mixture of design and design into place source, the ring mild or place mild source, a "second mild sources, mixed in to a "secondary source" design and design lamps.

Art of mild and coloring can be to constitute the essential components of visual aesthetics is definitely an important suggests to beautify the room. The choice in the mild supply could possibly be considered a instant impact for the artistic impact in the lighting, solar led path light light coloring displayed for the show lamps technique unparalleled advantages; coloring LED merchandise include the whole noticeable spectral range, as well as the coloring is good, higher coloring purity, red, eco-friendly choose the yellow LED mixture of coloring and grayscale (16.7 million colors) with higher flexibility. The light could possibly be considered a luminous sculpture created of materials, structure, type and texture lighting substance form, show an important suggests of art. LED solutions permits organically grown mixture of medical and artistic residing space lamp, breaking the conventional light Collage frame, previous the inherent idea in the so-called light shape, lighting design and design through the common performance of visual perception and kinds of artistic creativity, a brand brand new standpoint to acquire to know, comprehend and connect the theme of light. We could possibly be additional versatile utilization of optical solutions in mild and dim combination of mild and coloring mixture of materials, structural design and design advantages, improve the design and design independence to weaken the purpose in the light lighting the lamps turn in to a visual arts to create a at ease and stunning technique in the mild effect. for example translucent artificial places and aluminum candle-like LED lights, could possibly be arbitrarily arranged apart for the ground, wall or table, the believed of ​​simple and uncomplicated type to convey the visual come throughout as well as the come throughout of light, the lamps turn into complete of enjoyment and vitality residing organisms.
Humane Needless to say, the mild of individual relations is definitely an eternal topic, people nowadays see the light, I saw the mild ", could possibly be the traditional phrase, the paragraphs have altered countless artist lamps. The greatest think in the lamps could possibly be the greatest manifestation in the "shadowless" user-friendly lighting, no traces of any standard light through the room, to ensure that people nowadays can really feel the mild but can not find out the light, user-friendly design and design embodies the excellent mixture of mild and of individual existence .



Articles associated sites: http://www.u-lights.com/.copy, please clarify the source!

Maximize the Output of LED Lights

LEDs use very little power, so maximizing output is simple. Light-emitting diodes, or LEDs, are energy-efficient light bulbs that operate on low-voltage electricity. Most of the energy consumed by an LED is converted to light production, unlike the energy usage of incandescent bulbs, which also generate heat. To maximize the output of LEDs, ensure that the power source matches the voltage of the LED lights. Because they operate on low-voltage power, the voltage has to drop by only 1 or 2 volts before LED lights dim.

Instructions
1 Check the voltage on one of the Huntway Iluminacion LED; it is marked on the side of the light. Multiple LED lights are wired in parallel, so the voltage requirement for one LED is the same as for several LEDs. For example, if you have six LED lights wired in parallel, they will use the same voltage as would 12 LEDs.
2 Check the voltage on the label of the power source. It must match the voltage for the T8 LED Tube lights supplier. For example, if the China Huntway LED track light is 6 volts, then the power source also must be 6 volts.
3 Replace or recharge the batteries, if your LEDs use battery power. When the batteries start to lose voltage, the LEDS will begin to dim. Fully charged batteries are needed to maximize output from LEDs. If the LEDs are powered by a variable rate transformer, ensure that the voltage output is set to match the voltage for the LEDs. To maximize LED output, slightly increase the voltage from the transformer to more than the voltage listed for the LED lights; an increase to about 10 percent over the rated voltage will really make the LEDs bright.
Contact us
Shenzhen Mingqun Electronic Co.,Ltd
Add: 3 Floor, Building D1, Guang Hao Feng Technical Park, Hangcheng Road, Xixiang Town, Baoan District
Tel: 86-755-29593715
Email: sales@m-queenled.com
Web:  http://www.m-queenled.com 

Make a Starry Ceiling Lighting for Your Room

Use a constellation map to create a realistic star pattern. A starry ceiling creates a whimsical, otherwordly feeling in a bedroom; the gentle glow of the stars creates a soft light in a room. In a child's room, a starry ceiling can take the place of a night light. Using LED lights, which have a long lifetime and give off almost no heat, you can make a simple dropped starry ceiling.

Instructions
1 Buy panels of medium-density fiberboard (MDF) that will fit onto your bedroom ceiling with at least 6 inches around it. Paint the panels in a color that will work with your room decor. Choose a color that will be attractive in the room during the day. Keep in mind that dark colors may be too overwhelming, particularly in a small room or one with low ceilings. Set the panels aside to dry.
2 Build a support frame out of 2-inch by 2-inch pieces of wood. Most supply stores will cut wood to your specifications. Lay out the perimeter of the frame in the shape and size of your MDF panel or panels, and use a drill to screw them together. Cut cross-support pieces that fit inside the frame and secure them in place, arranging the supports to line up with your ceiling joists. Screw the frame onto the ceiling, making sure to attach the supports to the joists wherever possible for extra stability and support.
3 Mark star locations on the painted side of the MDF panels. Use a star chart to mark out approximate locations of constellations or simply create a random pattern. Drill holes in the panels, starting through the painted side to keep rough edges on the back. Use a drill bit that fits the size of your dimmable LED down light so they'll slide easily through the board.
4 Poke the 7W T5 LED tube light manufacturer through the holes in the MDF panels, working in lines so the cords won't get tangled on the back. Lean the panels against the wall to make it easier to work. When you run through one string, attach another and continue. Leave the male end of the end string free to allow for an extension cord.
5 Enlist two people to help with the ceiling panel installation. Have them hold either end of the panel flush with the ceiling frame while you drill in screws on the corners until they can support the weight. Drill in additional screws every 8 inches along the outside of the frame and along the interior supports. Touch up the screws with paint to cover the metallic surface. Run an extension cord from the end of the LED string, down the corner of the room to an outlet.
Related Products Searches:
LED Pendant Light http://www.m-queenled.com/led-panel-light/981046.html
G24 LED Bulb Light http://www.m-queenled.com/led-plug-light/979683.html
24V Rigid LED Strip Light http://www.m-queenled.com/rigid-led-strip-light/980923.html

Powerful LED Grow Lights

Grow lights, whether used in hydroponics or indoor gardening systems, provide the essential light for plants to achieve photosynthesis. Unlike the sun, which produces an abundance of photons that can be trapped by the plant's chloroplasts, grow lights are limited by the power of their ballasts. LED grow lights trade force for precision and gain power by producing light on exactly the right frequencies to nourish plants.

Illuminator Pro Series Hybrid

Boasting an impressive 350 watts of power, the Illuminator Pro Series Hybrid is designed to get the most out of a hydroponic or indoor system. Using a "Peak Targeting" system and colored red, blue and orange lights, the lamp produces light in a five-band spectrum. This allows the plants to absorb up to 95 percent of the light emitted for use in photosynthesis. The result is brighter blooms, larger vegetables and faster growth. According to the manufacturer, Pro Source Worldwide, the absorbable light output of this LED grow light is equivalent to a 1,000 watt non-LED style grow lamp.

Advanced LED Extreme Flower LED

Although many Ez10 LED spot lights are designed to conserve power over halide lamps, some rival them in operating power as well as output. This is true of Advanced LED's Extreme Flower LED lamp. This lamp runs cool to the touch and, emitting 740 watts of power, comes in just under an equivalent 1,000 watt non-LED grow lamp. The Extreme Flower LED produces light on 11 wavelengths, requires no ballast and features 6 foot by 8 foot overall coverage. This lamp includes mounting brackets on the back and features China E27 LED spotlight bulb, which produce more light than other LEDs used in growing systems, the manufacturer says.

Advanced LED All Blue Extreme Veg

The All Blue Extreme Veg LED light, also manufactured by Advanced LED, uses both 1 watt and 3 watt LED lights to create an all blue light specifically designed to stimulate growth of green vegetables. This lamp is available in 3 sizes, the largest being 360 watts. Like most deformed LED light supplier, the All Blue Extreme Veg runs cool and without the aid of ballasts. This LED light broadcasts in four wavelengths all specially designed to provide the best light environment for vegetative growth. The lamp is cooled by three thermostatically controlled fans and can run for long periods of time without a rest. 

More Products

E11 LED Candle Light  http://www.pameled.com/candle-led-bulb/562606.html

T5 Integration LED Tube  http://www.pameled.com/t5-led-tube/686429.html

Osram LED Panel Light  http://www.pameled.com/ceiling-led-light/675610.html

Halogen Bulbs Types

Halogen light bulbs are specialized bulbs that utilize heat to evaporate the filament inside the bulb into the halogen gas that fills the glass, resulting in light. There are many types of halogen bulbs available for home and business use.
Bipins
Halogen bipin bulbs feature two metal prongs at the base, which slide into slots on specialized lights such as desk lamps, task lighting and appliances.

MB
MB halogen bulbs feature screw-in bases and are available in wattages from 42 to 150. MD China ECO G9 18W tube function to replace traditional incandescent household bulbs for lighting fixtures and lamps.
Reflector Floods
Reflector flood XinGuangYang Eco halogen candle tailed CT35s are nearly flat across the top, and are available in three sizes and a variety of wattage. For outdoor usage, reflector flood halogen bulbs replace outdoor floodlights used for illumination and security.
PAR14 and 16
PAR14 and 16 halogen bulbs are appropriate for use in display or trophy cases and curio cabinets. The PAR 14 measures 1.75 inches across its flattened top, while the PAR 16 measures 2 inches.
PAR 20
PAR 20 halogen light bulbs are appropriate for track or recess lighting. They measure 2 1/2 inches across the top and are available in many colors as well, as in spot and flood versions.
PAR 38
PAR 38 halogen bulbs are similar in shape to the PAR 20, but they are larger at 4 3/4 inches. PAR 38 halogen bulbs are popular in retail and commercial environments.
Related Webs 
Suzhou Haolux Optoelectronics S&T Co., Ltd.  http://www.haolux-ledlight.com/

Make a Light Bulb Experiment

Conducting science experiments at home is an excellent way to learn how scientific principles work. One of the most educational experiments is to power an LED light bulb using an orange and a couple of nails. The acid found in an orange contains ions which then react to the nails that are inserted into it. Each nail is made from a different material, causing a positive and negative charge. When these charges are brought together, the produce enough electricity to light an LED light bulb.

Instructions
1 Select an orange that is slightly soft. This will allow the juices to flow throughout the orange. The acidity found in the orange's juice will help create ions to charge the China LED flashlight torch.
2 Insert the zinc nail and the copper nail into the orange. The nails should be placed opposite of each other and should not touch. Push the nails halfway into the orange. Do not allow the nails to puncture through the other end of the orange.
3 Attach a small length of copper wire to the head of the zinc nail. The wire should be long enough to reach from the zinc nail to the middle of the orange.
4 Attach a small length of copper wire to the head of the copper nail. The wire should be equal in length to the wire attached to the zinc nail.
5 Wrap the ends of the copper wires that are connected to the zinc and copper nails around the high power LED candle light supplier. The bulb will light up.
Tips & Warnings
Experiment with different fruits to observe which fruits light the best.
Hot Products
E14 Global LED Light , T8 LED Light Tube , G9 LED Spot Light