Introduction of led lights

White LED luminous efficiency has been a breakthrough 120LM / W, 15LM / W 8 times of incandescent, fluorescent 50LM / W 2 times. Led pool light spectrum ultraviolet and infrared components, so no heat, no harmful radiation. LED's luminous flux half-life greater than 50,000 hours, and can be used normally for 20 years, the life of the device are generally in more than 100,000 hours, which is 10 times the life of the fluorescent lamp, which is 100 times that of incandescent lamps, so basically not damaged, this lamp has a very good energy-saving long-life characteristics, continue to decrease as the price of white LED, the LED lights not only widely used in the holiday lights decoration, and gradually extended to the field of pavement lighting, commercial lighting, illumination requirements, full access to the practical and the environmental aspects of waste can be recycled, no the fluorescent mercury pollution problem, the national focus on the development of industrial projects.

 LED technology has been genuineness came to our front remarkable Olympics, both the opening ceremony on the magical picture and canvas, or the Water Cube exterior transform unpredictable colorful magic light, or a large number of actors who quintana a magical light, or even just as Galaxy and slowly rising Olympic rings, all are comprehensive application of LED technology.
 Advantage of environmental protection and energy saving led flood lighting: ◇ energy efficient: in the case of the same brightness, the one thousand hours of LED energy-saving lamps consume only 1 kWh of electricity consumption, ordinary incandescent 17 hours, one hundred hours of ordinary energy-saving lamps consume 1 degree electricity; ◇ Long life service life of up to eighty thousand hours, ten thousand hours in the life of the ordinary energy-saving lamps, ordinary incandescent lamp life of 1,000 hours. ◇ Healthy light does not contain ultraviolet and infrared energy-saving starting with me, no radiation, ordinary energy-saving lamps and incandescent light contains ultraviolet and infrared; ◇ green mercury and lead harmful elements, was conducive to the recovery and utilization , electromagnetic interference and does not produce harmful elements of ordinary lamp contains mercury and lead, and energy-saving lamps, electronic ballasts will produce electromagnetic interference; ◇ protect eyesight strobe; ◇ light efficiency high fever, 90% of the energy into visible light, ordinary incandescent DC drive, no flicker, normal lights are AC drive, it will inevitably produce 0% of the electrical energy is converted into heat, and only 20% of the electrical energy into visible light; ◇ safety factor required voltage current is small, less heat, no security risks, can be used in mines and other dangerous places; directly with 220V AC, challenges energy limit, the use of 220-volt power supply, built several pieces of miniature high-performance light-emitting beads, constant current The Manifold, design power for a small daily lighting of a lamp may meet an ordinary room, writing, reading and studying. Use ordinary meter, digital meter testing, meter basic fixed with 2 to 3 meters basically do not turn, and replacing ordinary incandescent lamp, the meter is fast rotation, the energy saving effect of immediate results, at a glance. Allow people to science, advanced, reasonable, legitimate and free electricity.

Its energy consumption as incandescent fortieth, one-third of the energy-saving lamps, intuitive and magical energy-saving effect, to attract the attention of consumers, the end of the "energy" energy-saving lamps misunderstanding is lighting lighting energy saving in the history of a major breakthrough with the epoch-making significance of innovation. 2, the health of photoinduced luminescence Manifold is the world's most state-of-the-art environmental green light, energy-saving super bright mini light beads from my start with a large angle, after layer delivery transformer, 6 to 24 volts of pure low DC drive real zero strobe, prolonged use will not make eye fatigue, with a high color rendering and high through sexual soft light approximate daylight, and does not produce color difference, can provide appropriate illumination. Work its own power consumption is minimal, so very small, fever, hand touch is an excellent and safe green cold light. Once the designer of the lights in the research and development of products based on the goal of illumination and diamond crystal point the refractive astigmatism design, light pro-and high light, through the nature of the request, the lampshade in the lamp beads Pai subcolumn point, linear, ring banded to form a more stable light source system, to achieve visual lighting with the best results. 3, LED life of up to 8-10 million hours, color stability, not of years affect the color difference.
The Source: http://www.solledlights.com http://www.led999.net/, http://www.m-queenled.com/, reproduced please specify the source, thank you!

Characteristics in the LED lighting

Led lighting led lamps collectively, using the additional maturity in the LED technology, LED will acquire additional as well as a great offer better progress through the residing space lighting the area of design and design and development. Bedroom lighting design and design through the 21st century could possibly be centered on led rigid strip lights design and design for the mainstream, completely embodies the energy, health, technique and user-friendly lighting and progress trends, the social dominant in the space lighting. through the brand new century, LED lighting lamps will certainly will brighten everyone's space to alter everyone's life, lighting progress and design and design of the awesome change.

Feature
Energy conservation review data exhibits that, in comparison with incandescent, fluorescent, ceiling led light source, semiconductor lighting for the atmosphere with out any pollution, energy-saving overall performance can attain additional than 90%. in the identical brightness, energy usage is only 1/10 of an common incandescent lamp, fluorescent tube 1/2. If 50% to replace the conventional lighting with LED, every twelve weeks of electrical power cost savings is equivalent for the sum of amid the three Gorges energy plant producing capacity, its energy overall performance is very impressive.
The well being in the LED could possibly be considered a eco-friendly light. DC LED light driver, no strobe; infrared and ultraviolet components, there is no radioactive contamination, the coloring is higher and consists of a luminous directional; common performance dimming, coloring temperatures alter does not create visual errors; chilly mild supply reduced in high fat calories and is also safe and seem to touch; they are incandescent and fluorescent reach. it could not merely provide at ease lighting space, but at the same time good to satisfy people's actual well being needs, shield their eyesight healthful and environmentally friendly mild source.
Due to scaled-down solitary LED power, reduced brightness, and should unquestionably not be utilized alone, while additional than one LED assembly produced getting sensible LED lighting consists of a broad app prospects. Lighting designers can ascertain the type in the light optical system, LED amount and sizing in the energy demands of lighting objects and luminous flux; may be also several LED LED mixture of design and design into place source, the ring mild or place mild source, a "second mild sources, mixed in to a "secondary source" design and design lamps.

Art of mild and coloring can be to constitute the essential components of visual aesthetics is definitely an important suggests to beautify the room. The choice in the mild supply could possibly be considered a instant impact for the artistic impact in the lighting, solar led path light light coloring displayed for the show lamps technique unparalleled advantages; coloring LED merchandise include the whole noticeable spectral range, as well as the coloring is good, higher coloring purity, red, eco-friendly choose the yellow LED mixture of coloring and grayscale (16.7 million colors) with higher flexibility. The light could possibly be considered a luminous sculpture created of materials, structure, type and texture lighting substance form, show an important suggests of art. LED solutions permits organically grown mixture of medical and artistic residing space lamp, breaking the conventional light Collage frame, previous the inherent idea in the so-called light shape, lighting design and design through the common performance of visual perception and kinds of artistic creativity, a brand brand new standpoint to acquire to know, comprehend and connect the theme of light. We could possibly be additional versatile utilization of optical solutions in mild and dim combination of mild and coloring mixture of materials, structural design and design advantages, improve the design and design independence to weaken the purpose in the light lighting the lamps turn in to a visual arts to create a at ease and stunning technique in the mild effect. for example translucent artificial places and aluminum candle-like LED lights, could possibly be arbitrarily arranged apart for the ground, wall or table, the believed of ​​simple and uncomplicated type to convey the visual come throughout as well as the come throughout of light, the lamps turn into complete of enjoyment and vitality residing organisms.
Humane Needless to say, the mild of individual relations is definitely an eternal topic, people nowadays see the light, I saw the mild ", could possibly be the traditional phrase, the paragraphs have altered countless artist lamps. The greatest think in the lamps could possibly be the greatest manifestation in the "shadowless" user-friendly lighting, no traces of any standard light through the room, to ensure that people nowadays can really feel the mild but can not find out the light, user-friendly design and design embodies the excellent mixture of mild and of individual existence .



Articles associated sites: http://www.u-lights.com/.copy, please clarify the source!

Maximize the Output of LED Lights

LEDs use very little power, so maximizing output is simple. Light-emitting diodes, or LEDs, are energy-efficient light bulbs that operate on low-voltage electricity. Most of the energy consumed by an LED is converted to light production, unlike the energy usage of incandescent bulbs, which also generate heat. To maximize the output of LEDs, ensure that the power source matches the voltage of the LED lights. Because they operate on low-voltage power, the voltage has to drop by only 1 or 2 volts before LED lights dim.

Instructions
1 Check the voltage on one of the Huntway Iluminacion LED; it is marked on the side of the light. Multiple LED lights are wired in parallel, so the voltage requirement for one LED is the same as for several LEDs. For example, if you have six LED lights wired in parallel, they will use the same voltage as would 12 LEDs.
2 Check the voltage on the label of the power source. It must match the voltage for the T8 LED Tube lights supplier. For example, if the China Huntway LED track light is 6 volts, then the power source also must be 6 volts.
3 Replace or recharge the batteries, if your LEDs use battery power. When the batteries start to lose voltage, the LEDS will begin to dim. Fully charged batteries are needed to maximize output from LEDs. If the LEDs are powered by a variable rate transformer, ensure that the voltage output is set to match the voltage for the LEDs. To maximize LED output, slightly increase the voltage from the transformer to more than the voltage listed for the LED lights; an increase to about 10 percent over the rated voltage will really make the LEDs bright.
Contact us
Shenzhen Mingqun Electronic Co.,Ltd
Add: 3 Floor, Building D1, Guang Hao Feng Technical Park, Hangcheng Road, Xixiang Town, Baoan District
Tel: 86-755-29593715
Email: sales@m-queenled.com
Web:  http://www.m-queenled.com 

Make a Starry Ceiling Lighting for Your Room

Use a constellation map to create a realistic star pattern. A starry ceiling creates a whimsical, otherwordly feeling in a bedroom; the gentle glow of the stars creates a soft light in a room. In a child's room, a starry ceiling can take the place of a night light. Using LED lights, which have a long lifetime and give off almost no heat, you can make a simple dropped starry ceiling.

Instructions
1 Buy panels of medium-density fiberboard (MDF) that will fit onto your bedroom ceiling with at least 6 inches around it. Paint the panels in a color that will work with your room decor. Choose a color that will be attractive in the room during the day. Keep in mind that dark colors may be too overwhelming, particularly in a small room or one with low ceilings. Set the panels aside to dry.
2 Build a support frame out of 2-inch by 2-inch pieces of wood. Most supply stores will cut wood to your specifications. Lay out the perimeter of the frame in the shape and size of your MDF panel or panels, and use a drill to screw them together. Cut cross-support pieces that fit inside the frame and secure them in place, arranging the supports to line up with your ceiling joists. Screw the frame onto the ceiling, making sure to attach the supports to the joists wherever possible for extra stability and support.
3 Mark star locations on the painted side of the MDF panels. Use a star chart to mark out approximate locations of constellations or simply create a random pattern. Drill holes in the panels, starting through the painted side to keep rough edges on the back. Use a drill bit that fits the size of your dimmable LED down light so they'll slide easily through the board.
4 Poke the 7W T5 LED tube light manufacturer through the holes in the MDF panels, working in lines so the cords won't get tangled on the back. Lean the panels against the wall to make it easier to work. When you run through one string, attach another and continue. Leave the male end of the end string free to allow for an extension cord.
5 Enlist two people to help with the ceiling panel installation. Have them hold either end of the panel flush with the ceiling frame while you drill in screws on the corners until they can support the weight. Drill in additional screws every 8 inches along the outside of the frame and along the interior supports. Touch up the screws with paint to cover the metallic surface. Run an extension cord from the end of the LED string, down the corner of the room to an outlet.
Related Products Searches:
LED Pendant Light http://www.m-queenled.com/led-panel-light/981046.html
G24 LED Bulb Light http://www.m-queenled.com/led-plug-light/979683.html
24V Rigid LED Strip Light http://www.m-queenled.com/rigid-led-strip-light/980923.html

Powerful LED Grow Lights

Grow lights, whether used in hydroponics or indoor gardening systems, provide the essential light for plants to achieve photosynthesis. Unlike the sun, which produces an abundance of photons that can be trapped by the plant's chloroplasts, grow lights are limited by the power of their ballasts. LED grow lights trade force for precision and gain power by producing light on exactly the right frequencies to nourish plants.

Illuminator Pro Series Hybrid

Boasting an impressive 350 watts of power, the Illuminator Pro Series Hybrid is designed to get the most out of a hydroponic or indoor system. Using a "Peak Targeting" system and colored red, blue and orange lights, the lamp produces light in a five-band spectrum. This allows the plants to absorb up to 95 percent of the light emitted for use in photosynthesis. The result is brighter blooms, larger vegetables and faster growth. According to the manufacturer, Pro Source Worldwide, the absorbable light output of this LED grow light is equivalent to a 1,000 watt non-LED style grow lamp.

Advanced LED Extreme Flower LED

Although many Ez10 LED spot lights are designed to conserve power over halide lamps, some rival them in operating power as well as output. This is true of Advanced LED's Extreme Flower LED lamp. This lamp runs cool to the touch and, emitting 740 watts of power, comes in just under an equivalent 1,000 watt non-LED grow lamp. The Extreme Flower LED produces light on 11 wavelengths, requires no ballast and features 6 foot by 8 foot overall coverage. This lamp includes mounting brackets on the back and features China E27 LED spotlight bulb, which produce more light than other LEDs used in growing systems, the manufacturer says.

Advanced LED All Blue Extreme Veg

The All Blue Extreme Veg LED light, also manufactured by Advanced LED, uses both 1 watt and 3 watt LED lights to create an all blue light specifically designed to stimulate growth of green vegetables. This lamp is available in 3 sizes, the largest being 360 watts. Like most deformed LED light supplier, the All Blue Extreme Veg runs cool and without the aid of ballasts. This LED light broadcasts in four wavelengths all specially designed to provide the best light environment for vegetative growth. The lamp is cooled by three thermostatically controlled fans and can run for long periods of time without a rest. 

More Products

E11 LED Candle Light  http://www.pameled.com/candle-led-bulb/562606.html

T5 Integration LED Tube  http://www.pameled.com/t5-led-tube/686429.html

Osram LED Panel Light  http://www.pameled.com/ceiling-led-light/675610.html

Halogen Bulbs Types

Halogen light bulbs are specialized bulbs that utilize heat to evaporate the filament inside the bulb into the halogen gas that fills the glass, resulting in light. There are many types of halogen bulbs available for home and business use.
Bipins
Halogen bipin bulbs feature two metal prongs at the base, which slide into slots on specialized lights such as desk lamps, task lighting and appliances.

MB
MB halogen bulbs feature screw-in bases and are available in wattages from 42 to 150. MD China ECO G9 18W tube function to replace traditional incandescent household bulbs for lighting fixtures and lamps.
Reflector Floods
Reflector flood XinGuangYang Eco halogen candle tailed CT35s are nearly flat across the top, and are available in three sizes and a variety of wattage. For outdoor usage, reflector flood halogen bulbs replace outdoor floodlights used for illumination and security.
PAR14 and 16
PAR14 and 16 halogen bulbs are appropriate for use in display or trophy cases and curio cabinets. The PAR 14 measures 1.75 inches across its flattened top, while the PAR 16 measures 2 inches.
PAR 20
PAR 20 halogen light bulbs are appropriate for track or recess lighting. They measure 2 1/2 inches across the top and are available in many colors as well, as in spot and flood versions.
PAR 38
PAR 38 halogen bulbs are similar in shape to the PAR 20, but they are larger at 4 3/4 inches. PAR 38 halogen bulbs are popular in retail and commercial environments.
Related Webs 
Suzhou Haolux Optoelectronics S&T Co., Ltd.  http://www.haolux-ledlight.com/

Make a Light Bulb Experiment

Conducting science experiments at home is an excellent way to learn how scientific principles work. One of the most educational experiments is to power an LED light bulb using an orange and a couple of nails. The acid found in an orange contains ions which then react to the nails that are inserted into it. Each nail is made from a different material, causing a positive and negative charge. When these charges are brought together, the produce enough electricity to light an LED light bulb.

Instructions
1 Select an orange that is slightly soft. This will allow the juices to flow throughout the orange. The acidity found in the orange's juice will help create ions to charge the China LED flashlight torch.
2 Insert the zinc nail and the copper nail into the orange. The nails should be placed opposite of each other and should not touch. Push the nails halfway into the orange. Do not allow the nails to puncture through the other end of the orange.
3 Attach a small length of copper wire to the head of the zinc nail. The wire should be long enough to reach from the zinc nail to the middle of the orange.
4 Attach a small length of copper wire to the head of the copper nail. The wire should be equal in length to the wire attached to the zinc nail.
5 Wrap the ends of the copper wires that are connected to the zinc and copper nails around the high power LED candle light supplier. The bulb will light up.
Tips & Warnings
Experiment with different fruits to observe which fruits light the best.
Hot Products
E14 Global LED Light , T8 LED Light Tube , G9 LED Spot Light

Composition of LED Lightbulbs

LED light bulb components. LED (light-emitting diode) lighting is considered a type of energy-efficient lighting. This means that the energy it takes to power an LED is relatively low in proportion to the device's high light output. There are advantages and disadvantages associated with the few components that make up traditional LED lights.

Components
According to the website eere.energy.gov, LEDs consist of two electrodes (an anode and a cathode), a whisker, an anvil, a semiconductor and a lens, all contained within an epoxy resin. Power enters 3W E27 LED bulb manufacturer systems through the anode. Electrical current then runs through the whisker, then the semiconductor and anvil. The current exits through the cathode. The epoxy housing focuses light produced by the bulb and protects the inside components from the outside elements. Color is determined by the chemical make-up of the bulb's semiconductor.
Size
Light-emitting diodes are the smallest form of light bulb on the market. Each Orientalight high power 100W LED factory light is constructed to a diameter of around 1/4 inch. The size has severely restricted LEDs' practical applications to instrument and electrical panels until recently. LED technology has evolved and increased its presence in the lighting industry with the development of "clustering." These light bulbs are clustered into groups of any number of LEDs, broadening their applications.
Facts
Properly manufactured LEDs can last for well over 45,000 hours, according to eere.energy.gov. All components of an LED are securely fastened into a solid epoxy shell. This makes the bulb very durable and able to withstand a certain level of jarring without breaking. Most types of light bulbs utilize delicate filaments in their construction; LEDs, however, require no filament, which adds to their durability.
Features
Often when LEDs are clustered to form a light bulb that fits typical incandescent bulb sockets, they feature diffuser lenses. Diffusers are also used in LEDs for track lighting and flashlights because the lenses broaden the beams of light emitted by the light bulb. Part of the reason that LEDs last for so long is that they do not operate at high temperatures, according to the website eartheasy.com.
Cost
LED technology is linked with a very high cost of production, which is directly reflected in the average price of LEDs. One of the reasons for high production costs is that LEDs currently use sapphire-based technology in the construction of every LED. Silicon wafer-based technology is being researched at Purdue University. Replacing costly sapphire-based technology with silicon wafer-based technology promises to make LEDs much more affordable. The website treehugger.com notes that clustered 8W SMD3528 T5 LED tube lights supplier that fit into everyday sockets are available for $60 and up.
Related Searches
IP65 Outdoor 60W Marine Led Flood Lights 24W CREE Jewelry LED DownLights 600x600mm Super Brightness Office LED Lighting Panels

Street Lights Tips

Our street lights should keep us safe while still being as efficient as possible. Street lights are present in almost every town. They give night time walkers a feeling of safety. However, there are ways to improve upon the technology that is currently present in our hometowns. Making our street lights as energy and cost efficient as possible should be considered one of the top priorites when looking to improve these lights.

Solar Lights
Solar street lights provide a high level of brightness and efficiency in addition to their long life and lack of conventional energy consumption. They are also fairly easy to install. These types of street lights are typically used in industrial parks, scenic areas, urban and district roads, many pedestrian streets and in many parking lots. They are both energy efficient and green, as it produces no pollution and can have a life of up to 20 years with little maintenance. They charge their batteries using energy from the sun, thus they require no electrical current, saving taxpayer dollars and reducing energy cost and consumption.
Fiber Optic Lighting
Fiber optic lighting is another method of reducing energy costs. They are also known as "light pumps" and "remote source" lighting. These systems create their light at a separate factory, then send it through fiber optic cables laid into the ground. These bulbs rarely need to be replaced, thus reducing maintenance and replacement cost. The only significant cost related to this type of commercial street light would be the expense of laying fiber optic cables from the remote lighting facility to the high bay induction lamp. They also produce no heat in the bulb. They are typically used in outdoor signs, theatre stage lighting and hazardous locations, as well as in street lights.
Induction Lighting
Another efficient type of lighting is induction lighting. Also known as electrode-less lighting, this type of street light consists of a generator, a power coupler and a lamp. As the name implies, there are no filaments or electrodes present in the lamp. These lamps have large power factors and fast ignition and re-ignition times, so it wastes less energy when firing up. These lamps also have a 100,000 life hour rating, over four times the normal fluorescent and HID bulbs. These bulbs have a wattage ranging from 23 to 165 watts, so you can find something almost always to fit your lamps and your lighting needs.
LED Lighting
Another tip for how to improve your energy efficiency is to install LED, or light emitting diode, lights into our street lamps. This method of lighting our streets can take many incarnations. There are five types currently being employed: the integral, retrofit, solar, high pole, and tunnel street lights. The electrodeless induction ceiling lights are expected to maintain 50,000 hours of life between bulbs. They also are rated to save as much as 75 percent of the energy that traditional bulbs use.

Decorative Accent Lighting

Add Floralytes to these glass vessels and turn lovely into captivating. Back in Grandma's day, party tables were lavished with baskets and jars filled with freshly cut flowers. These days, your choice of party decoration materials is limitless, particularly now that inexpensive LED lights operating for long periods of time on individual batteries are readily available. The Floralytes brand has a reputation for being reliable and affordable, so when you're ready to light up the night at your next party, look for their name on the package.

Floralytes 101
Floralytes are small but mighty t8 LED tube lights engineered to make decorative lighting magic on a shoestring budget. Every Floralyte has an on/off switch so you can control the number of lights you want lit in your centerpieces any time you like. Replaceable batteries in each Floralyte last from 48 to 50 hours and color is never a problem, since Floralytes come in amber, orange, red, blue, green, teal, white, pink and violet. Need extra drama? The RGB Floralyte flashes red, green and blue in sequence.
Clean the Glass Centerpiece Vessel First
Whether you fill tall glass vases with white Floralytes to create the illusion of jars of fireflies, or you plan to mix and match the decorative LED light panels with flowers, food or other fanciful elements, it's important to begin your centerpiece project with a sparkling clean receptacle, as light emanating from the LED highbay lamp will call attention to everything from fingerprints to dirt on the glass. A microfiber cleaning cloth and window spray will tackle dust inside and out. Dry the vase thoroughly, especially if you plan to add confetti or glitter, so nothing sticks to the glass.
Floralyte Flower Arrangement
Floralytes require no wiring, so you have complete freedom to create an exotic, lit floral arrangement. Fill a vase with glass marbles and lit Floralytes so the "soil" into which the flowers will be placed reflects the light of the glass. Next, arrange silk flowers in the vase and pop a Floralyte into the center of each so the flowers light up too. Place the vase on a mirrored pedestal. Mirrored reflections of the piranha LED module light in the vessel and blossoms create a dazzling display.
Fruit or Vegetable Floralyte Display
You've seen them on cruise ships. Create lavish displays of fruits and vegetables that emulate fine art, using a little imagination. Start with a focal point. Place a pineapple, upside-down spray of bananas, tall pumpkin or another natural food in the center of a large, round, footed glass pedestal. Fill in the remaining space with juicy grapes and strawberries or rows of cut veggies. Tuck Floralytes in coordinating colors into the display and watch guests' eyes light up when they spot your delicious arrangement.
Float Your Floralytes
Since Floralytes are waterproof, surprise your children with kid-pleasing centerpieces at their next party. Drop weighted plastic pirate ships into fish bowls, fill with water and add RGB Floralytes. Your pirate-themed centerpieces will flash red, green and blue throughout the party. As guests leave, have each child pluck a light from a bowl as an extra favor. Little things really do mean a lot when you're a kid!
More to Explore
Clear Bright Enterprise Group Ltd http://www.led999.net/
SHENZHEN CHAMPION OPTO-ELECTRONICS CO., LTD. http://www.top-led-china.com/

How To Make a LED Auto Headlights

If you'd like to install LED auto headlights on your car, you will need to purchase an LED headlamp assembly that is made for your vehicle. If the LED assembly is not produced specifically for the make and model of your vehicle, it may not fit properly. Fortunately, LED headlamp assemblies can be purchased online for practically every vehicle, even older models. Once you have the LED assembly, installing it is the same as installing a regular headlamp assembly.

Instructions
1 Turn the engine of your vehicle off. Open the hood and disconnect the battery by using a socket wrench to loosen and remove the negative terminal from the battery post.
2 Disconnect the electrical connector of your vehicle's headlight assembly by squeezing in the plastic tabs on the connector and pulling it off the assembly. You will now be able to remove the entire headlight assembly. Most assemblies are held in place by bolts or screws, so remove all fasteners using a socket wrench or a Phillips screwdriver as appropriate. Once all are removed, you can easily pull the assembly out of the engine compartment.
3 Install the replacement LED assembly and refasten the bolts or screws. Reattach the electrical connector. Reconnect the negative terminal to the battery. Test the China Car LED Lights. If they are functioning properly, close the hood. If not, check the connection of the LED headlights and try again. If that does not work, there may be an issue with the assembly or it is not compatible with your vehicle.
Related Products
Auto LED Tail Lights
LED Light Bulbs
LED Spotlights

Make Small Tube Lights

Old lightbulbs can become stylish, free-standing lights. The term "tube light" refers to the cylindrical shape of an old-fashioned lightbulb, also known as an Edison bulb. Any oblong, thin lightbulb can become a functioning lightbulb again with a little ingenuity, so don't toss those antique bulbs you find at garage sales or in your grandparents' attic. Recycle them into a free-standing light for your desk or put a few modified lightbulbs together to create lighted centerpiece displays or Halloween decorations. Steampunks and sci-fi fans especially love these colorful, homemade pieces.

Instructions
1 Put on surgical gloves and safety glasses to protect your hands and eyes from bits of glass and glue.
2 Turn your China LED tube lights upside-down. Locate the purple glass terminal encased in the brass fitting on the bottom of the bulb. Grip the glass with pliers and squeeze until you hear the glass crack. Slowly pull the pieces of glass out with the pliers.
3 Turn the bulb right-side up so the filaments inside the LED bulb lights manufacturer fall out. Discard the filaments and the broken glass.
4 Fill the bulb about 7/8 full of rubbing alcohol. Drip a few drops of food coloring (if desired) into the alcohol -- for a steampunk look, add golden-orange colors; for a science-fiction effect, try green.
5 Place the full bulb upside-down into a cup.
6 Turn on a battery-powered LED mini light to check that its bulb works. Smear E600 adhesive all over the sides of the LED light. Slip the light, bulb facing down, into the tube lightbulb so that the bottom of the Orientalight G24 LED lights sits level with the edge of the lightbulb's brass fitting. The fit must be very snug.
7 Allow the adhesive to dry overnight. Turn on the LED light so it illuminates the colored alcohol. Turn the bulb right-side up.
Tips & Warnings
LED mini-lights lights are usually shaped as small, squat cylinders. You can find mini lights in many dollar stores.
References
Ledorientalight Company : http://www.orientalighting.com/

How To Identify GE Light Fixture

Light fixtures provide more than just light to find our way around the house at night. They also add beauty and interest. General Electric (GE) offers both residential and commercial lighting products, including outdoor, recessed and track light. Consider your lighting needs before investing in lighting products. You can purchase GE products both online and at retailers.

Architectural
The Architectural series of lighting features Haolux LED light fixtures on small tracks that are either completely straight or that can curve. For example, the Tetra Contour light comes on a flexible track and produces a neon-like light. These lights come in different colors and use a 24 volt direct current (DC) power supply. The lights are up to 40 percent more efficient than standard neon lighting. The lighting lasts for about 50,000 hours of use.
Signage/Transportation
GE makes commercial lighting for both the sign and transportation industry. Both use LED lighting systems, and the sign lights look like neon lights. For example, the LED rail signal fixtures include both wayside, crossing and special application lights. The Level Crossing China LED tunnel lights comes in either 8- or 12-inch models.
Indoor
The GE indoor series of lights includes high bay, low bay and garage LED panel lights manufacturer. The high bay lighting is for ceilings over 30 feet, and the low bay lighting is for ceilings at or below 30 feet. An example of the garage lighting is the UltraStar VP-Series Vapor Tight light, which features twist-and-lock sockets. The reflectors have an aluminum finish, and the mounting is made of stainless steel. You can install this light fixture in both wet and dry areas. It come with an 18-month warranty on the fixture and a five-year warranty on the ballast.
Outdoor
GE offers six types of outdoor lights: flood, area, roadway, hazardous location, stadium and poles and brackets. For example, the Decaflood 400 Powerflood Floodlight provides security during the evening hours. The housing of this unit is made of copper and die-cast aluminum, and the reflector has a coating that is resistant to wear and corrosion. Install this model facing either outward or downward.
Refrigerated Display
The refrigerated display lighting series is similar to track lighting and be used for illuminating refrigerator display cases. For example, Immersion RV40 LED lighting provides up to 16 watts of lighting per case door and lasts for up to 50,000 hours of use. This lighting comes with a five-year warranty and is available in a 60-inch size.
Other household fashion lamps click here!

How To Make Flickering LED Candle

Do-it-yourself LED candles are a cheap and easy project. They only cost a few dollars and are great alternative sources of light to have around the house. They use very little energy because they use LED (light emitting diodes) technology and they only take about 10 minutes to make once you have all of the supplies. Whether you are looking for ambiance or emergency lighting, LED tail candle bulbs are easy to make and great to have around the house.

Gather Your Supplies
Your candles can be as simple or elaborate as you choose. This can turn into as creative as a project as you make it. To make the light pick up flicker 10 MM dimmalbe A60 LED bulb lamp (you can find these easily online, or in the decorative lighting section), 9 volt batteries, 9 volt battery clips, 100/220 OHM resistors, wire connectors, wire cutters and some duct tape.
Buy tacky putty to stick the batteries to the base. This can be found in most floral sections at hardware stores and at any nursery. For the base and cover buy a small glass ashtray and go to an art store and choose decorative scrapbook paper or vellum. Pick up some spray adhesive to close the light cover.
Connect the LED to the Battery
Start with the resistor and straighten the wires on each side so you can tell which wire is positive and which is the negative. They are marked -- but straighten them so they are easily distinguished. Bend the wires over so they are easier to work with and keep together. Grab the black negative lead from the battery connector and expose a bit of the wire by trimming back the black plastic coating with your wire cutters. Now bunch the resistor wires and the negative lead together with a wire connector by shoving them inside. Use your needle nose pliers and pinch the connector to ensure that all the wires are making contact. Once the negative side is connected, it's time to move onto your other connections which will be pinched together in the same fashion.
Bunch the positive side (long side) of your LED with the other side of the 100/220 OHM resistor. Repeat the process with the same process with the wire connector and pliers to seal this together. Connect the negative LED short wire to the long, positive wire on another LED. Twist the wires together. Again, repeat the sealing process with the wire connector and pliers.
Trim the red positive wire on the battery until it's about an inch long. This will make it easier to bundle. Also trim down and peel a bit of the red plastic off the end of the red positive wire. Twist the positive battery wire and negative LED par20 light wire together. Repeat the process with the wire connector and pliers until the wires are sealed together.
Now that all for connectors are complete, it's time to bundle them together neatly so that the LEDs are pointing up and the connectors are pointing down. Duct tape works well for this. Just wrap it up like tiny sticks of dynamite. To make an on-and-off switch, bend a couple of the metal pieces on the battery clip connector using the needle nose pliers. Connect the battery to the unbent battery clip and then slide the clip over until it's touching the battery. This turns the LED on and allows you to turn the light on and off easily without having to disconnecting it completely.
Make the Light Cover
Now that the technical stuff is complete, it's time to get creative. Attach a small wad (about the size of a quarter) of putty to the center of an ashtray. Place the battery into the putty and press down until it's secure.
It's time to make the light cover using scrapbook paper or vellum. You can find some great paper at art stores or you can download any design you like on your computer and simply print it out at home on vellum. Vellum is a translucent stock paper that will allow light to shine through a design. This is a great trick for making holiday lights. Attach the paper to the ashtray by inserting the paper into the grooves of the ashtray, making a circular lampshade for the candle. Cut the paper down to size then spray one edge with spray adhesive. Overlap the edges and press together. Once this is dry, place the shade back into the groove of the ashtray, turn on the LED low power SMD spotlight and you are done. You have made an LED candle that will last for about 36 hours.
Related Products
LED Tube Light T8
Gemanled LED High Bay Light
DimmaBle LED Panel Light

Make Your Own Screw in LED Lightbulb for the Household

LEDs generate light with very little heat loss. LEDs -- Light Emitting Diodes -- are solid state electronics, meaning they have no moving parts. This makes them much more energy-efficient and longer-lasting than standard incandescent light bulbs. The old-style bulbs use a metal filament super-heated by the electric current; it inefficiently converts the energy to light and heat. LEDs, however, convert the majority of the electric energy to light with very little heat. They don't use a filament so there is nothing to burn out, giving LEDs more than 16 times the life of standard bulbs 

Instructions

1 Remove the reflector and base from the China ECO halogen bulb. Carefully work the screwdriver to scrape out the cement that holds the bulb together. Slowly and gently work the pieces of the bulb apart until you separate the glass, base and reflector.
2 Cut the aluminium sheet in a circle that will fit inside the reflector of the bulb. The higher up it sits in the reflector, the more bulbs you will be able to fit, but less area for reflection. Work the aluminium sheet to fit about half-way down in the reflector.
3 Punch holes in the aluminium for the LEDs to fit through. Most office hole punch tools will have about a 5 millimeter hole, and most XinGuangYang ECO Halogen Candle C35 used in holiday lights are the same size. Place as many holes as you can on the aluminium sheet without overlapping. Start in a circle around the outside edge and then make another circle inside that. You should be able to fit between 18 and 22 LEDs.
4 Remove the LEDs you will need from your holiday light set. If yours is equipped with a rectifier, cut that out to make the LEDs work with alternating current (AC) rather than direct current (DC). Older-style Haining ECO standard halogen lamp holiday lights did not use a rectifier but rather used paired LEDs, one for each direction of the AC. If you do not have a rectifier, remove the LEDs in pairs. Pull the bulbs out of the plastic housing. If there is any shell or colored cover on the bulb, remove with pliers until you see the bare LEDs. Note how the LEDs connect to the wire in the light string so you can re-connect the wire in the bulb.
5 Fit the LEDs into the aluminium disc through the holes you punched. Super glue them in place and hold them until the glue dries. Cut off some of the wiring from the holiday light string and strip off the insulation. Connect the leads on the LEDs to the wire, duplicating the way they are wired in the light string; twist the bare wire together with one or two twists. If you have a rectifier, connect that at the end of the circuit of lights in the bulb. Secure all the connections with electrical tape.
6 Glue one wire from the LEDs (or rectifier) to the side wall of the bulb base and the other wire to the bottom connection of the bulb base. Since LEDs use DC instead of AC, it doesn't matter how you connect them inside the bulb. Hot-glue the base to the reflector, and the glass to the reflector. Screw the bulb into a lamp and enjoy the LED light.

Can a Plant Grown Under LED Lights?

Many bonsai trees need 16-to-18 hours of consistant indoor light to thrive. When growing bonsai indoors, it is crucial to supply them with a consistent light source that allows them to photosynthesize and grow. While many indoor light sources are available, LED lights have many advantages, as well as a few disadvantages, for indoor bonsai growth. By selecting the correct plants to grow under LED lights and making sure that your setup allows for enough access to light, you can grow a fine bonsai with China LED panel lights.

Trees and Shrubs That Grow Well Indoors With LED Lights

First, you must consider which types of plants adapt well to bonsai techniques, LED lighting and indoor gardening. Hardy deciduous and evergreen trees, such as maples and pines, rarely do well indoors and under Orientalight LED high bay lights because they require winter conditions for their growth cycle. Tropical trees might do well indoors since they cannot handle cold conditions. Fig trees, fukien tea trees and dwarf pomegranate shrubs can be adapted to indoor bonsai gardening using LED lights.
Advantages
The primary advantage to growing bonsai with LED lights is that LED lights use much less energy than other lighting methods. They allow a grower to tailor the red and blue spectrum of light; blue light helps encourage growth, while red light regulates and slows growth to promote flowering. LED lights also produce little heat. LED lights last between five and 12 years, requiring less frequent replacement than other types of lighting. Because light is so important to bonsai growth, a less expensive light source readily used by the plant helps the plant to not only survive but also thrive.
Disadvantages
LED lights are initially expensive to install; one LED tube lights manufacturer without mounting equipment cost about $300 as of 2011; one LED bar provides enough light for five or six bonsai plants. If an individual light in an LED array dies, it is generally necessary to replace the entire light apparatus because specific LEDs in an array are typically not replaceable. LED lights also do not provide heat, which may reduce the growth of plants that need a warmer environment than room temperature to flourish.
LED System Choices
Choose an LED system that suits your needs. If you only want to use the lights for growing the plants, consider a red and blue array. This will provide only the colors from the light spectrum that the plants need for growth and reproduction. If you will use the lights to grow as well as display your bonsai, look for a full-spectrum system. Many LED light systems require a separately purchased mount that holds the lights sturdily above your plants.

Grow Under a LED Light

Recycle Christmas lights to make a grow light. Building an LED grow box can help to provide enough light for your plants to grow during the winter. It also can give you more space to grow plants by allowing you to grow them in crawlspaces or closets. Gardeners use grow boxes mostly for sprouting plants that they will later plant outside in their gardens. Use LED lights rather than regular bulbs because China Led bulb light do not produce as much heat, which can damage young plants.

Instructions
1 Put the lid on your rubber tub. Press it to make sure that it is secure.
2 Put a ¼ inch drill bit on your drill.
3 Count the number of Ejai Led tube light on your string of Christmas lights.
4 Drill the same number of holes into the lid. Space them evenly across the entire lid, but you do not need to measure them exactly. Spacing them evenly will ensure that all of the plants in the box are getting the same amount of light.
5 Press the Haining Led flood light through the holes.
6 Plug in the LED lights. Use an extension cord if necessary.
7 Place the plants inside the grow box and close the lid. Turn the lights on for at least eight hours per day.

Make A White LED Driver Circuits

You can build a simple but effectve LED driver by using a linear voltage regulator. White LEDs operate at a minimum forward voltage of 3.3 volts. This is higher than standard red, yellow or green LEDs. Like all LEDs, however, it requires a driver that can deliver a constant current at the proper voltage. You can build a simple but effective LED driver by using a linear voltage regulator to build a parallel China LED driver circuit. A linear regulator is not as efficient as a switching regulator, but it requires fewer parts to build a working circuit. This circuit can drive four, or more, white LEDs in parallel.
Instructions
 

Wire the Regulator Circuit
1 Plug the regulator into the breadboard.
2 Connect one end of a jumper wire to the INP (left) pin of the regulator. Connect the other end of the jumper wire to the supply strip at the top of the breadboard.
3 Connect one end of a jumper wire to the GND (middle) pin of the regulator. Connect the other end of the jumper wire to the ground strip at the bottom of the breadboard.
4 Connect one lead of the 0.47 microfarad capacitor to the INP pin of the regulator. Connect the other lead to the ground strip.
5 Connect the positive lead of the 22 microfarad capacitor to the OUT (right) pin of the regulator. Connect the other lead to the ground strip.
6 Connect the negative (black) lead of the battery holder to ground strip.
7 Connect the positive (red) lead of the battery holder to the supply strip.
8 Insert the batteries in the battery holder.
9 Attach the positive probe of the voltmeter to the OUT pin of the regulator.
10 Attach the negative probe of the voltmeter to the ground strip or the grounded lead of one of the capacitors. The voltmeter display should indicate 5 volts.
11 Remove the positive lead of the battery holder from the supply strip for now.
Wire the LEDs in Parallel
12 Connect one lead of a 68 ohm resistor to the power strip.
13 Connect the other lead of the resistor to the positive lead (usually the longest of the two leads) of an LED.
14 Connect the negative lead of the Topband dimming LED driver to the ground strip.
15 Repeat steps one through three for the remaining LEDs.
16 Reconnect the positive lead of the battery holder to the supply strip. The four LEDs should light up.
Tips & Warnings

• You should initially build this on a solderless breadboard for testing. If you are not familiar with solderless breadboards, see the link titled "The Electronics Club: Breadboard" in the Resources section for more information.

Build Your Own LED Lights

Using super-bright LEDs, you can make low-cost replacements for halogen bulbs. Fluorescent tubes have a lower power consumption than incandescent bulbs, but they still use more energy than LEDs. According to Andrew and Alexandru of LED Ideas, you can replace a fluorescent tube with LEDs fixed into a length of clear acrylic sheet and housed inside a clear plastic cover. You can also replace halogen bulbs with low-power LEDs by re-using the case of an old bulb as a housing for your LED array.
Instructions
 

1 Mark the strip of acrylic sheet with rows of three marks at 1 3/8 inch intervals, beginning 1 1/2 inches from one end, using the dry-wall T and utility knife. Drill out the holes using a drill press; you can use a hand drill but the results won't be as accurate.
2 Place three LEDs in the first row of holes. All of the long (positive) legs must be on one side and all of the shorter (negative) legs on the other, in a vertical row. One of the LEDs should have its positive leg facing the edge of the plastic strip. The PD LED light bulbs at the other end of the row should have its negative leg facing the opposite edge.
3 Solder the LEDs together. Solder the negative lead of the middle LED to the positive lead of the LED with its negative lead nearest the edge. Solder the positive lead of the middle LED to the negative lead of the LED with its positive lead nearest the edge. Leave the leads at the far ends of the row free.
4 Place the next row of three LEDs (LED triplet) into the plastic strip, maintaining the same positive-negative orientation as in the first row. Solder as before.
5 Snip the free negative leg of one LED triplet leaving 1/4 inch behind. Do the same to the leads of a 2.7 ohm resistor. Solder one lead of the resistor to the trimmed negative lead of the LED.
6 Solder a rail of copper wire along all the free positive leads of the China LED strip lights. Solder a similar rail along all of the free resistor leads.
7 Install the current regulator on the empty end of the plastic strip. Place the whole strip inside the plastic tube. Solder and install the end caps. Test your tube light using a 1A 12V power supply before installing it.
Tips & Warnings The designers of the LED spotlights manufacturer recommend using it in a solar system or as one of a number of such lights running from a large switching mode power supply.

Replace Fluorescent Tubes With LEDs

LED light tubes are popular replacements for the long, fluorescent light tubes, as they can last much longer and don't contain toxic mercury. Most of these tubes are designed to simply fit into the fluorescent light fixtures you already have; you can just remove the fluorescents, install the LEDs and you're done. Some LEDs, however, will work better if you remove the ballasts within the light fixtures that work with the fluorescents. This requires a slight bit of electrical work to replace the bulbs.
Instructions
 

1 Consult with the vendor that you get the LED high brightness bulbs manufacturer if you need to remove the ballasts in your light fixtures. Some LEDs can still work with the ballasts of fluorescent fixtures, but might still might cause problems with the amount of power consumed.
2 Make sure the light switch has been off for at least 30 minutes to an hour. Detach and remove the acrylic (or other type material) shielding covering the fluorescent bulbs if you use such a cover.
3 Disconnect the bulbs and store them away safely. Do not throw them away or place them somewhere that they might break.
4 Open the China LED flood light to the ballasts on the light fixture. Twist the metal tabs on the edges of each panel to remove them.
5 Locate the ballast and disconnect it from the wires at both ends by removing the wire nuts or cutting the wires. Pay attention to how the wires are lined up before you cut them.
6 Connect the wires on both sides together by stripping an inch off the insulation, twisting the bare wire together and wrapping it in electrical tape. You must connect each wire to the one that was directly opposite it on the other side of the ballast. If the red and black wires looked like they were connected through the ballast, connect them now.
7 Install the good quality LED tube in place of the fluorescents in the fixtures. Close up the ballast panels and replace the acrylic cover. Turn the lights on to test them.
Tips & Warnings
Dispose of the fluorescent bulbs properly, taking them to the recycling center in your area that takes these bulbs and batteries.

Change Christmas Lights to LEDs

LED lights shine brighter and are more economical than traditional lights. If you want to make a statement with your Christmas lights, consider replacing the old bulbs with Haining Ejai LED high bay light . LED lights produce more wattage per bulb at a fraction of the cost, which makes them an excellent choice for replacing traditional Christmas lightbulbs. Replacing the lights is easy to do and will draw a lot of attention to your outdoor Christmas display.
Instructions
 

1 Unplug the lights from the wall outlet. Make sure that there is no electrical current running through the Christmas lights when you replacing the bulbs.
2 Remove the traditional bulbs from the string of lights. Gently hold the bulb between your thumb and forefinger and pull it out of the housing.
3 Compare your old bulbs with the new LED street lamp lights to make sure you've got the right size. If you still have it, check the box the lights came in to see what size the bulbs were. You can also take a bulb to the store and ask for help in determining the proper-size LED.
4 Remove the LED bulbs from the package. Carefully inspect the package to determine how much wattage it uses. Anilumin LED bulbs use less wattage than typical lights, so more of them can be strung together. If the package says they are 0.04 amps, then you can get string together about 20 to 30.
5 Replace the bulb by pushing the LED into the housing until it snaps in place. Once all the bulbs are installed, plug the string in to test it out.

Make Your Own Screw-in LED Light Bulb

Making your own screw-in LED light bulb is a great way to save money and to go green. An LED is a light emitting diode, and some companies offer regular screw-in bulbs with the incandescent part replaced with LEDs. This helps save money because Zoom focus head lamps use less power and last longer than regular incandescent bulbs. Another added benefit is that LEDs generate close to no heat so less air conditioning is needed to deal with the heat given off by regular light bulbs.
Instructions
 

1 Place the screw-in light bulb plug down in front of you. Unscrew the plastic replica bulb off of the socket and place it to the side. You are going to use it in another step, so do not lose it. Place down 10 LEDs in a line in front of you. Twist a wire lead from the first LED to a wire lead from the second LED. Twist the free wire lead on the second LED to a wire lead on the third LED. Repeat this twisting process until only the first and last energy saving compact induction lamp have a free wire lead.
2 Twist the free wire lead from the first LED into the positive electrical post on the top of the screw bulb plug. Take the free wire lead from the 10th LED and twist it onto the negative electrical post. The posts have a plus and a minus symbol next to them to denote their polarity.
3 Wrap all the exposed wire leads in electrical tape, but do not wrap them together. Wrap the wires separately to keep them from shorting the circuit. You are making a simple series circuit, and shorts will break the entire circuit. Do not cover the light emitting parts of the professional LED ceiling light with tape or it will cut down on the light given off.
4 Push the LEDs into the plastic bulb and then re-screw it to the screw-in plug. Screw the plug into a light socket (with the socket off) and then turn the light on. If the light does not come on, then one of the connections was not twisted properly and came lose. Take the bulb apart and re-twist all the connections to be sure.

Wire LEDs

You can wire your own LEDs for a project. LEDs, also known as light emitting diodes, can be very useful because of the amount of light emitted with only very little power use and very little heat dissipated. They can be easily added to any project, but they have distinctive characteristics that set them apart from incandescent bulbs when it comes to safe, effective wiring. Plan and wire your China LED bulbs carefully to avoid destroying them and to help with future maintenance.
Instructions
 

1 Plan your wiring for the future. Even though the life an LED is longer than that of an incandescent light bulb, it still has a finite lifespan. Because LEDs have two lead wires and do not have a base that they can plugged or screwed into, you will need to plan accordingly. Never solder the LEDs directly to your project unless you only need it to work for a short time.
Get some disconnectors. Some disconnectors can be crimped to connect to the lead wires on the LED spotlights manufacturer. The longer lead on the LED is the positive side. Crimp one disconnector to the LED and another to a wire to connect to the power source.
2 Provide enough power to maximize the amount of light the LEDs give off. LEDs will light up when underpowered, but it is better practice to provide adequate power.
Look for the specifications on the LEDs you have purchased or are considering purchasing. Find the diode forward voltage requirement for the LEDs. This is the voltage you will need to provide for each LED in a series configuration. The following list contains the typical diode forward voltage requirements for different color LEDs if you cannot find the manufacturer's specifications.
Blue (430 nm) 4.6 V
True Green, Blue, White 3.3 V
Green 2.2 V
Yellow 2.1 V
Red or Orange 2.0
Calculate how much power you will need according to this list or manufacturer's specifications. For example, if you want to wire 3 red Twinkle LED corn lamp in your project then (3 x 2V = 6V) you will need to provide 6 volts of power (4 AA or AAA batteries will work).
3 Provide a resistor to protect the LEDs. The resistor will reduce the current so the LEDs are not destroyed. Calculate the LED resistor value with the following formula:
LED Resistor Value, R=(supply voltage - LED voltage) x LED current
When using a 6V power source such as 4 AA batteries, the supply voltage equals 6V. The LED voltage for red LEDs is 2V. Use the LED current provided in the manufacturer's specifications. If the current is not provided, use 20 mA. Using these values in the formula, yields (6V-2V) x 20mA, or 80 ohms minimum resistance. A 100 ohm resistor will work fine.
4 Use heat-shrink wrap or electrical tape around any connections or exposed metal in your wiring. This will help avoid a short circuit that may cause your LEDs to be destroyed.
5 Continue to add additional Haolux LED PAR lamps in series and wire and connect each that same way as described. The LEDs should be connected positive to negative. You can change the number of LEDs or the color but you will need to calculate the required power and resistor needed.
Tips & Warnings
Finish your circuit completely before applying the power source. Put in the batteries or plug into the wall (if using an AC to DC converter or power brick) last.

Replace Fluorescent Bulbs With LED Bulbs

Making the switch to LED lights saves money and energy. LED lights are more efficient and safer than typical fluorescent lights. LEDs do not contain toxic mercury chemicals, nor do they burn out as fast. The majority of huntway LED track lights are designed to fit inside the fluorescent tube housing, so installing them is fairly simple. Making the switch to LED will save money and energy for your home or building.
Instructions
1 Ensure the light switch for the fixture you will be changing the lights in has been off for about 30 minutes. This is important in preventing any electrical shock when disconnecting the bulbs. It also helps in the lights being cool, as fluorescent lights may become hot when lit for a while. Remove the material shielding the bulbs. This shield may disconnect completely or hang from a hinge.
2 Disconnect the fluorescent bulbs from the fixture and either store them or dispose of them. Make sure they are disposed of properly--not in a local landfill, but through a proper recycling station. Be careful not to break the bulbs as this may cause injury. Open any windows to ventilate a room if the lights are broken to prevent mercury inhalation.
3 Locate the ballast fittings on the fixture and disconnect them from the light fixture, if necessary for the China LED ceiling light to fit. Some LEDs may be able to fit in the present ballast, but some may not. Refer to the manufacturer's directions to see if the ballast needs to be replaced.
4 Remove the wires, paying special attention to how they are situated so you know how to rewire the fixture when inserting the LED PAR lamp factory. You may need to use a screwdriver to remove the ballast fitting in order to reach the wires.
5 Strip an inch or so off of insulation from around the wires with a wire-stripping tool, carefully removing the insulation via a 45-degree angle. Twist the bare wire together and wrap it with electrical tape. You will need to connect the wires opposite of the ballast. Connect the wires just as they were before the ballast fittings were removed.
6 Place the concave LED diode manufacturer in the fixtures like the fluorescent lights were fitted. Put one in each light fixture and screw it until the light fits snug. Place the cover back over the lights. Turn the light switch to the on position to test the lights. If they come on properly, then all the wiring is correctly connected.

Install LED Under Car Kits

Give your car a glow with an LED under-car kit. People who love their cars are always looking for new ways to add a little extra style. A great way to accomplish that is installing an Anilumin LED corn light . Your car will stand out from the rest on the road as it emits a soft light from its underbelly. This can be a fun way to impress friends and show off at a car show.
Instructions
1 Park your car in a flat work area. Ensure the emergency brake is engaged. Gain access to your car's battery and disconnect it.
2 Look under your car to find a suitable installation spot. This spot should be clear of any moving parts, fuel lines, anything that generates heat, exhaust systems, or places where a car jack would lift the car.
3 Use your car's jack to jack up the car so you can fit-test the LED tube in your kit. Use the directions that came with your LED under-car kit for ideas about where to mount the LED tubes. You are looking for a spot that is centered with respect to the car's overall length, and sits on the chassis so the tubes are not visible.
4 Attach the mounting brackets to the T8 SMD tube manufacturers and lift into the installation location. Use the mounting brackets as a template to mark where you will punch holes with your pencil. Set the mount and tube assembly aside. Use your center punch to cut out holes at the marks you just made.
5 Protect the holes you just punched out from rust by applying a little silicone seal.
6 Slip the screws into the mounting brackets. Align the brackets up to the holes you just made so everything lines up. Use your drill with screw attachments to tighten into place the brackets and LED tube assembly. Repeat this process until each of the T8 SMD tube manufacturers assemblies is attached.
7 Find a location to mount the distribution block. This location should be a flat surface clear of any moving parts and heat sources, ideally, high inside the engine compartment. Connect all of the tubes' wiring to the distribution block's outputs.
8 Find a location for the LED under-car system's controls in your car. Using a hole located in the engine compartment's firewall, plug the controls into the distribution block.
9 Lower the car carefully down onto its wheels. Locate the positive terminal of the car battery and connect the power wire from the concave LED diode system's controls. Connect the negative grounding wire of the LED under-car system's controls securely to the car's chassis or an existing grounding wire.
10 Reattach the battery and start the car. Test all lighting systems through the LED under-car system's controls.

Use LED Lighting for a Video

LED lights, light emitting diodes, work by converting electricity into light. LED lights are more durable than traditional fluorescent or incandescent lighting, and when turned on LED light panels provide a steady stream of non-flickering light, according to NAHB Research Center. China LED lighting for video lighting can be an ideal way to illuminate a scene as these lights do not run hot and they provide an even glow, which is ideal for illuminating a subject.

Instructions
1 Purchase the appropriate lighting panel for your use. The size of an LED light panel depends on how much of the subject you will need to light. A standard video light setup should have a medium-sized light panel with a smaller mini panel to counterbalance shadows. If you will be interviewing a person on video, a ring-shaped LED panel will cast an attractive glow on the subject without causing a white-out on the subject's skin.
2 Set up the lights. Use the larger LED panel light manufacturer as your key light, which is the brightest light within the setup. Position the light as you would with a standard incandescent light, usually at about a 45-degree angle diagonally in front of the subject. Balance the light given by the key light by setting up a fill light. This light should be smaller than the key light and around 50 to 75 percent dimmer. Most LED light panels have a built-in dimmer, which does not alter the color of the light but simply changes its brightness. Position the fill light on the opposite side of the subject to remove shadows created by the key light.
3 Adjust the brightness levels of the LED light panels. Because LED light panels do not get hot, you can place the lights as close as needed to the subject without the fear of burning or whiting out the subject. Once you have positioned the lights and adjusted their brightness, call "Action" and let the magic of filmmaking begin.
Tips & Warnings
Purchase at least three different professional LED street lighting. Depending on the shot you wish to create, you may need to place more than two lights on the subject.
Set light angles and levels by referencing your video camera monitor to get a sense of how the subject looks on film. Do not simply set up the lights and begin filming. Take time to establish the light locations and play with the brightness levels of the panels until you have the ideal lighting situation.

Way to Use an LED Grow Light Panel

United LED grow lights are used in greenhouses and small indoor gardens. You can change the light wavelengths to produce the spectrum of light that a particular plant needs. LEDs are more energy efficient than traditional grow lights; they use less energy, last longer and produce little heat. They are so efficient that NASA uses them as grow lights in space.
Instructions

1 Research your plant to determine its light needs, and most efficient day and night cycles.
2 Measure one foot above the maximum growing height of your plant, and mark the height on the wall with a pencil. Mount the LED Globe Bulb manufacturer according to manufacturer's instructions at this mark.
3 Set the electrical light timer to the correct time. Program the on and off intervals of the timer to control the day and night cycle. Plug the LED grow light into the timer.
4 Monitor the carbon dioxide levels of the air. Some Haining LED Panel Lights may emit a large amount of absorbed light that may change the carbon dioxide levels in the air. Use a carbon dioxide generator to add carbon dioxide as needed, up to 1500-parts per million.

Different Kinds of LED Strip Lights

Accent an area with a strip comprised of various LED colors. Find light emitting diodes, or LEDs, in a variety of devices such as digital clocks, backlighting of computer and television screens, sensors and calculators. Strip lighting with Yihao LED strip lights provides an energy-efficient way to create a mood or accent in any area. Choose from a variety of several types of LED strip lights to match your decor.

Flexible and Rigid Strips
Find LEDs embedded in flexible strips, such as ribbons or rope, which is cut to specified lengths and used for decorative or frame lighting. Buy LEDs affixed to rigid strips or tubes for decorative or under-the-counter lighting.
Waterproof Strips
Purchase waterproof, weatherproof and submersible LED strips. Similar to regular China LED Bulb Light, except for the addition of a waterproofing agent such as a silicon rubber sheath, install them along wet locations such as pool decks, fountains and ship railings as both accent and primary lighting.
Color Changing
For specialty accents, install color-changing LED strips. Choose between red, green or blue in many different combinations of color and brightness. Color controllers provide customers with a number of creative options. Create different flickering speeds and color pattern combinations for retail window displays.
Dimmable LED Strips
Many types of LED strip lights are adjustable with the use of a dimmer switch. Since not all ECO Halogen Bulb manufacturers are adjustable, be sure to purchase a strip that is, if you wish to have this option.

Information About LED Lighting Transformer

Information About LED Lighting Transformer
LED Lighting Transformer Information A Light Emitting Diode (LED) is a lighting system that has been around since the 1960s. China LED Downlights are small in size, but can be grouped together to create large amounts of light. All LEDs require a transformer, which regulates the flow of electricity into the lighting system from the power source.

What is a Transformer?
A transformer is made from two coils of wound wire that are connected so that one of the coils will send electricity to the other. One of these coils, the primary coil, is connected to the electrical power source, and it sends electricity to the other, called the primary voltage. The way in which the two coils are connected decides the level of voltage in the second coil. The transformer can either increase or decrease the level of voltage running into it. The turns ratio is the measure of this change.
There are several different types of transformers. However, almost all PD LED Spotlights work with magnetic transformers, due to their reliability. It is not recommended to use any other type.
LEDs
LED lights are made out of small, 1/4 inch-wide diodes. For larger lights, many small ones are grouped together. Conventional light works by heating up a metal filament inside the light until it glows with heat. LEDs do not heat up a filament, and therefore light up without giving off very much heat, making them an excellent option for lighting systems in which heat is a concern. They are also much more energy-efficient that standard lighting systems.
LED lighting comes in two different types: mains voltage LED and low voltage LED. Mains voltage LED Tube Lights are quite simple and can be connected to conventional lights. However, low voltage LEDS require a transformer. Basic Low Voltage LED Transformers
LED transformers are usually built into the LED fixture or they come inserted into the plugs for portable LED devices. Low wattage LED transformers usually take in about 120 volts of alternating current (AC) from the outlet at a time and convert it to 12 or 24 volts of direct current (DC). The transformer will usually have a total amount of wattage that it can handle, and the number of lights it can be used for must have a lower total wattage than this level.
Other Types of Transformers
Larger LED transformers for products such as garden lights come in two forms. They are either box-shaped or toroidal (donut-shaped). They can be placed anywhere that is convenient. They come in black weather-proof boxes and can be placed on buildings, fences, or walls and under decks or even manholes.
If you cannot find a place to hide your transformer above ground, you can buy a Ground Burial Transformer, especially designed to be buried but still protected. It are specially built so that no moisture can get into the transformer. This process is called resin sealing, and it protects the transformer from dangers such as seepage or condensation.
Uses of LEDs
Once you have the proper transformer for your Gemanled LED Ceiling Lamp, you can use it for a wide variety of both indoor and outdoor lighting tasks.
Indoors, LEDs can be used anywhere in any way you might desire, including staircases, hallways, living rooms, kitchens, nurseries and bathrooms.
Outdoors, LED lights are widely used for gardens, decks, patios and driveways.